Material Data Center is a leading international information system for the plastics industry. Material Data Center offers a comprehensive plastics database, calculation tools, CAE interfaces, a literature database and an application database. For more information about Material Data Center visit www.materialdatacenter.com.

This is the free Material Data Center Datasheet of Ultramid® B3WG10 GIT BK23210 - PA6-GF50 - BASF

Check here, which other Ultramid B datasheets, application examples or technical articles are available in Material Data Center

Caratteristiche Fisiche - Proprietà Meccaniche - Proprietà Termiche - Altre Proprietà - Proprietà Specifiche Materiale - Funzioni

Any use of this information falls under the rules of our disclaimer.

Testo del prodotto

Injection moulding grade, glass fibre-reinforced, heat stabilized, special for Gas Injection Technology.

Caratteristiche Fisiche	secco/cond	Unitá	Norma del test
ISO Data
Ritiro di stampaggio, parallelo	0.3 / *	%	ISO 294-4, 2577
Ritiro di stampaggio, perpendicolare	0.7 / *	%	ISO 294-4, 2577

Proprietà Meccaniche	secco/cond	Unitá	Norma del test
ISO Data
Modulo a trazione	16500 / 10500	MPa	ISO 527
Carico unitario a rottura	235 / 155	MPa	ISO 527
Deformazione a rottura	3.1 / 5.9	%	ISO 527
Resistenza all'urto Charpy, +23°C	107 / 104	kJ/m²	ISO 179/1eU
Resistenza all'urto Charpy, -30°C	99 / 95	kJ/m²	ISO 179/1eU
Resistenzia all'urto Charpy con intaglio, +23°C	18 / 23.8	kJ/m²	ISO 179/1eA
Resistenzia all'urto Charpy con intaglio, -30°C	14.7 / 14.6	kJ/m²	ISO 179/1eA

Proprietà Termiche	secco/cond	Unitá	Norma del test
ISO Data
Temp.di inflessione sotto carico, 1.80 MPa	210 / *	°C	ISO 75-1/-2
Temp.di inflessione sotto carico, 0.45 MPa	220 / *	°C	ISO 75-1/-2

Altre Proprietà	secco/cond	Unitá	Norma del test
Massa volumica	1570 / *	kg/m³	ISO 1183

Proprietà Specifiche Materiale	secco/cond	Unitá	Norma del test
ISO Data
Numero di viscosità	115 / *	cm³/g	ISO 307, 1157, 1628

Funzioni

Caratteristiche

Processabilità e Forma di Forni

Stampaggio ad Iniezione

Forma fisica disponibile

Pellet, Nero

Additivi

Agente di distacco

Caratteristiche speciali

Stabilizzato o stabile al calore

Disponibilità geografica

Europa

Altre informazioni

Stampaggio ad Iniezione

PREPROCESSING
Pre/Post-processing, max. allowed water content: .15 %
Pre/Post-processing, Pre-drying, Temperature: 80 °C
Pre/Post-processing, Pre-drying, Time: 4 h

PROCESSING
injection molding, Melt temperature, range: 280 - 310 °C
injection molding, Melt temperature, recommended: 300 °C
injection molding, Mold temperature, range: 80 - 120 °C
injection molding, Mold temperature, recommended: 100 °C
injection molding, Dwell time, thermoplastics: 10 min

Disclaimer

Copyright Altair Engineering GmbH. Altair Engineering GmbH assumes no liability for the system to be free of errors. The user takes sole responsibility for the use of this data under the exclusion of every liability from Altair Engineering GmbH; this is especially valid for claims of compensation resulting from consequential damages. Altair explicitly points out that any decision about the application of materials must be double checked with the producer of this material. This includes all contents of this system. Copyright laws are applicable for the content of this system.

Created: Source: www.materialdatacenter.com

Material Data Center is provided by M-Base Engineering + Software GmbH. M-Base Engineering + Software GmbH assumes no liability for the system to be free of errors. Any decision about the application of materials must be double checked with the producer of this material.

Additional information about this material, like producer contact address, etc. can be found at www.materialdatacenter.com. For access to this extra information a registration is requested. Free online registration is available.